SGI InfiniteStorage 4000 Series Uživatelská příručka Strana 63
- Strana / 122
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Replacing a Failed Disk Drive
007-4834-001 45
7. Review all documentation shipped with the new drive module for any updated
replacement procedures and other information. If necessary, modify the remaining
steps to meet the system requirements. Kits often contain the most current servicing
information. If the kit instructions conflict with those in this procedure, follow the
kit instructions.
Caution: If the temperature of the shipping or storage environment differs
significantly from the temperature of the environment in which the drive module
will be installed, acclimate the drive module before you install it.
8. Wearing antistatic protection, slide the new drive module fully into the slot.
Caution: Partial insertion of a drive may cause the controller to mark other drives
on the same bus as failed. Install a drive in one complete motion. Make sure that you
insert it all the way into the slot and lock it into place.
9. Lower (close) the lever. Wait for the new drive to spin up.
10. Check the drive service, drive fault and drive activity indicators on the new drive
module. The activity indicator (right LED) should be on (either blinking or steady)
and the drive service and fault (left and middle LEDs) should be off.
Note: The fault indicator may flash intermittently while the drive spins up. The
activity indicator blinks when data is being written to the new drive module.
11. Based on the status of the drive Active and drive Fault lights, choose one of the
following actions.
• The drive service action LED is off – go to the next step.
• The drive Active light is on and the drive Fault light is off – Go to the next
step.
• The drive Active light is off – The drive might be installed incorrectly. Remove
the drive, wait 30 seconds, and then reinstall it. When finished, go to the next
step.
• The drive Fault light is on – The new drive might be defective. Replace the
defective drive with a new drive, and then go to the next step.
12. See the applicable software procedures (for TPSSM or other system software) for
instructions on bringing the drive module back online.
13. Complete any remaining Recovery Guru procedures, if needed.
!
!
- InfiniteStorage™ 4000 RAID 1
- User’s Guide 1
- Record of Revision 3
- Contents 5
- 007-4834-001 vii 7
- About This Guide 13
- Important Information 14
- Chapter Descriptions 14
- Related Publications 15
- Conventions 16
- Product Support 16
- Reader Comments 17
- System Features 19
- 2 007-4834-001 20
- Performance Features 21
- RAID Controller Features 22
- Availability Features 23
- Supported Platforms 23
- System Components 24
- Storage Enclosures 25
- 8 007-4834-001 26
- 007-4834-001 9 27
- 10 007-4834-001 28
- 007-4834-001 11 29
- 2. Storage Enclosures 31
- Overview 33
- 16 007-4834-001 34
- 2: Storage Enclosures 34
- The Disk Drives 35
- RAID Controllers 35
- 18 007-4834-001 36
- Power Supply and Fan Modules 38
- Tray ID Selection 39
- Link Rate Switch 40
- SFP Transceivers 40
- 007-4834-001 23 41
- Figure 2-9 SFP Transceiver 41
- Turning the Power On 43
- 26 007-4834-001 44
- 007-4834-001 27 45
- 28 007-4834-001 46
- 007-4834-001 29 47
- Turning the Power Off 48
- 007-4834-001 31 49
- Checking the Indicator Lights 50
- Rear Indicator Lights 52
- 36 007-4834-001 54
- Moving the Enclosure 55
- Removing the Enclosure 56
- 007-4834-001 39 57
- Reinstalling the Enclosure 58
- Front Bezel Air Filter 59
- 42 007-4834-001 60
- Replacing a Failed Disk Drive 61
- 44 007-4834-001 62
- 007-4834-001 45 63
- 46 007-4834-001 64
- Alarm Mute button on the 64
- 007-4834-001 47 65
- 48 007-4834-001 66
- 007-4834-001 49 67
- Figure 4-5) 68
- Replacing an SFP Transceiver 69
- 52 007-4834-001 70
- 54 007-4834-001 72
- 007-4834-001 55 73
- 56 007-4834-001 74
- Upgrading Drives 75
- 58 007-4834-001 76
- 007-4834-001 59 77
- 60 007-4834-001 78
- Adding Expansion Enclosures 79
- 62 007-4834-001 80
- 5. Cabling 81
- 64 007-4834-001 82
- 007-4834-001 65 83
- 007-4834-001 73 91
- 74 007-4834-001 92
- 007-4834-001 75 93
- 76 007-4834-001 94
- 007-4834-001 77 95
- 78 007-4834-001 96
- 007-4834-001 79 97
- 80 007-4834-001 98
- Powering On the System 99
- 82 007-4834-001 100
- 5: Cabling 100
- Rack Specifications 101
- Rack Dimensions 102
- 007-4834-001 85 103
- Rack (empty) 104
- Each system 104
- 007-4834-001 87 105
- Area Requirements 106
- Wiring and Power 107
- Power Requirements 108
- Power Distribution Units 108
- Power Cords and Receptacles 108
- 007-4834-001 91 109
- Environmental 110
- Enclosure Specifications 111
- System Enclosure Air Flow 115
- Electromagnetic Emissions 117
- Product Safety 118
- Electrostatic Discharge 118
- Shielded Cables 119
- FCC Warning 119
- VDE 0871/6.78 120
- European Union Statement 120
- Attention 121
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce